Dual Light Path Photothermal Catalytic Evaluation Units
TK-DPTC dual optical path photothermal catalysis system is suitable for photothermal co-catalysis, evaluation and screening of photocatalytic catalysts.
It is mainly applied to high-temperature photothermal catalytic reaction, photothermal co-catalysis, which can be specifically used in the fields of synthesis and sintering of semiconductor materials, preparation of catalyst materials, evaluation of activity of catalyst materials, hydrogen production by photolysis of water, oxygen production by photolysis of water, reduction of carbon dioxide, gas-phase photocatalysis, photocatalytic degradation of formaldehyde gas, VOCs, NOx, SOx, nitrogen fixation and so on.
TK-DPTC dual optical path photothermal catalytic system (<5MPa) is a set of fixed-bed photothermal reaction device used to complete the evaluation and screening of catalyst activity, applicable to gas, liquid or gas-liquid feeding at the same time; gas-solid, liquid-solid, gas-liquid-solid reaction, able to achieve automatic control of the temperature, gas-phase flow rate, liquid-phase flow rate, the reaction temperature is able to achieve the programmed temperature rise (linear heating), through the programmed temperature rise settings The heating time and holding time of the experimental temperature can be set through the programmed heating, and the experimental products under different pressures and temperatures can be tested and analysed on-line in stages with the GC and other analytical instruments.
System Advantages
1.Pressure-reducing system in the system, which can be directly connected with the reaction gas cylinder, the pipeline is equipped with proportional unloading valves, high-precision pressure gauges and pressure sensors, and all temperature control points and pressure monitoring points are equipped with over-temperature and over-pressure alarms for automatic interlocking protection.
2.Feeding system, when passing into different gases, the corresponding gas flow coefficient can be selected or inputted in the flow coefficient table, so as to realise the diversity and accuracy of gas types.
3.Mezzanine temperature-controlled standard gas module, reaction liquid such as toluene, ethanol, etc. in the pressure-resistant tube, pass into the reaction gas or inert gas into the module, bring the effective gas of ppm level into the reactor, control the temperature of the module and then control the concentration of the gas through the water-bath circulating water machine; thus, it can greatly reduce the cost of the experiment and solve the difficult problem that the standard gas is expensive.
4. Constant pressure system, with low pressure and high pressure dual pressure system, according to the experimental pressure to select the corresponding pressure system, to provide stable and accurate, stable experimental environment for the catalyst.
5.The system control all adopts PLC software automation control, real-time monitoring of the reaction process, automated data processing, and provide a full set of experimental programmes. The screen adopts industrial control touch screen PLC, which can be used to change the programme at any time according to the demand. Xinshi Ke shinsco provides gas chromatograph, liquid chromatograph, electrochemical workstation, TPR, TPD, SPV, TPV, Raman and other testing and analysis instruments.
6) The system integrates feeding system, constant pressure system, steady flow system, preheating system, reaction system, product collection system and PLC control system.
Main technical parameters:
1.Pressure: photothermal catalysis pressure <5MPa (design pressure 8Mpa), conventional thermal catalysis pressure <5MPa (design pressure 10MPa).
2.Temperature: <800ºC; constant temperature of working area: length 30mm, <±1ºC; heating furnace: 2 sections;
3.Reactor working area light: diameter 30mm, double-sided irradiation, using quartz reaction tube, quartz light guide tube;
4.Quartz reaction tube, effective working area 30mm, diameter 10mm, built-in temperature measurement probe, light area <10cm2, catalyst loading <1ml, pressure resistance <5MPa;
5. Placement of filter and converging lens at the position of light inlet to achieve the selection of spectrum and adjustment of light intensity;
6.Pre-heating furnace parameters <5MPa, <600ºC, to improve the mixing effect and warm the reaction gas in advance to ensure the reaction temperature during catalysis;
7.gas-liquid mixing module, often used temperature range: -10 ºC ~ 95 ° C; design pressure: 5MPa; material: stainless steel 316L; with water bath jacket; the top of the air inlet, outlet, temperature measurement port and liquid port, the bottom of the liquid discharge port;
8.condenser: design pressure: 6MPa; material: stainless steel 316L; 300ml; coil condenser, leaving two water nozzles for connecting condensate.
9.Gas-liquid separator :Design pressure:6MPa;Material:Stainless steel 316L;150ml;internal de-bubbling plate, the gas is discharged from the top and the liquid is deposited at the bottom.
10. Control requirements: must use Mitsubishi or Siemens PLC control system, data acquisition and feedback control timely and reliable: temperature control accuracy: ± 1 ºC; pressure control accuracy: ± 0.1Mpa; gas flow control accuracy: ± 1%; liquid flow control accuracy: ± 1%.
11. three-way gas: you can choose any gas (containing dozens of gas options), N2 flow rate: 50, 100, 100ml/min
12. all the way liquid: containing spare liquid pipeline and liquid heating, liquid flow <5ml/min, <200 ºC, metering pump options;
13.Gas chromatograph GC: double FID + TCD three detectors + nickel-metal hydride conversion furnace programme, you can test all components, the use of pneumatic autosampling valve 10-pass + 6-pass (temperature control <200 ° C) to achieve the simultaneous analysis of the three detectors test online, to achieve the full-component analysis, anti-control automatic workstations.
Package Detail
1) Wooden packing
2) The goods can be shipped by sea, air or train, small goods or spare parts will be shipped by express.
3) You can choose your own freight forwardwe as well.
4) Door to Door Delivery to save your energy and time. We'll take the all risks during transportation.
Shipping Details
1) AMERICA:3-8 working days.
2) ASIAN:3-8 working days.
3) EUROPE:5-10 working days.
4) OCEANIA:4-9 working days.
5) AFRICA:7-13woring day.
Xi'an Taikang Biotechnology Co., Ltd, is a famous manufacturer of Lab equipment located in the central China. Now has TAIKANG, TKA two well-known brand trademarks. The main products include ultra-high temperature and high pressure reactor, high pressure photochemical reactor, supercritical high pressure reactor, high pressure glass reactor, micro high pressure reactor, high pressure ultrasonic reactor, Ultra-high temperature hydrothermal synthesis reactor, photocatalytic reactor, visual catalytic reactor, hydrothermal synthesis reactor, rotary evaporator, parallel synthesis reactor, high and low temperature circulator, high and low temperature high pressure tubular reactor and other equipment and so on.
Specialize in this field for more than 20 years,TKA brand instrument has own high reputation in more than 70 countries and regions, provide technical support for tens of thousands organizations to solve problems within their research, special for university, research institutes, industries, inspection agencies, etc. Promoting technology progress and improving human life is TKA social mission.
We welcome new and old customers from all over the world to contact us for future business relationships and achieving mutual success!!
Q1:Are you trading company or manufacturer?
A1:We are professional manufacture of lab equipment and we have our own factory which is a high-tech enterprise integrating R&D, production and sales. And welcome to visit our factory.
Q2: How long is your delivery time?
A2: Usually, delivery time is 30-45 days after receiving your payment.
Q3:How to shipping the replacement parts?
A3:We will according the actual situation to choose the suitable shipping ways. For small parts we shippin by Express.
Q4: How about your quality warranty ?
A4: Normally all TKA products are supplied with a warranty of 12 Months from the date of shipment.
Q5: Do you accept OEM and ODM orders?
A5: Yes,We accept.
Q6:What is your terms of payment?
A6:Payment≤15,000USD, 100% in advance. Payment≥15,000USD, 40% T/T in advance, balance before shipment.
Q7:Can we visit your factory?
A7: Welcome visit our factory.
Audited Supplier 
){kind=link}